Skip to content

DIY Baby Plaster Mold 3D Hand Foot Print Mold for Baby Souvenir Hand Casting Kit Couples Wedding Accessories Home Decor Gifts

$1.53

Category:


Price: 1.53

Package Included:
100g x molding powder
100g x plaster
1 x powder (gold lacquer/silver lacquer lacquer/pearl lacquer)
1 x brush
Note: The frame is not included. This is generally only enough for a baby double or a foot.
 
Dosage reference:
1.0-3 months: one hand (clone powder 60g + water 160ml) (model powder 80g + water 50ml)
Single foot (clone powder 80g + water 200ml) (model powder 100g + water 70ml)
2.3-12 months: one hand (clone powder 100g + water 250ml) (model powder 150g + water 100ml)
Single foot (clone powder 150g + water 400ml) (model powder 200g + water 130ml)
3.2 years old – 4 years old: one hand (clone powder 150g + water 400ml) (model powder 200g + water 130ml)
Single foot (clone powder 200g + water 500ml) (model powder 250g + water 160ml)
4.5 years old – 12 years old: one hand (clone powder 200g + water 500ml) (model powder 250g + water 160ml)
Single foot (clone powder 250g + water 600ml) (model powder 300g + water 200ml)
5. Adult one-handed: (cloning powder 300g + water 1100ml) (model powder 600g + water 500ml)
6. Adult hands: (clone powder 500g + water 1600ml) (model powder 1200g + water 800ml)

Note:When
Choosing a container, you must first shape your hands and put them in. There is a small amount of space around the bottom and surrounding areas without your hands touching the container. The container should not be too large. The clone powder is suitable for 10-20 degrees of water temperature. The higher the water temperature, the faster the solidification. The model powder can be tap water at room temperature.

INSTRUCTIONS:

1. Mix the molding powder with3 to3.2 times the amount of powder (300 to 320 mL). Stir quickly until mixture is as smooth as possible. The mixture will turn a purple/pink color.Remember not to add too much water to the mixture.
2. After 1 minute, place baby's hand or foot into this purple molding mixture at once. Please make sure the hand or foot is completely submerged, and doesn't break the surface of the mixture or touch the edge of cup.
3. Try to keep your baby's hand or foot as still as possible while the molding mixture is setting.
4. Hold your baby's foot in the mold for 240 more seconds to ensure the mold is fully set, then you can very carefully and smoothly remove their hand or foot from the mold.
5. To ensure a smooth release from the mold, wiggle slightly back and forth so that air can enter the opening of the mold.
6. Once the hand or foot has been removed, Open bag of plaster powder 50g, and mix with 1/3 to 1/2 of the amount of water (80 to90 mL). Stir as quickly until the mixture is as smooth as possible.Do not add too much water to the stone powder. The higher the concentration the stronger the casting will be.
7. Slowly pour the stone powder mixture into the opening of the mold.Gently jiggle the mold while pouring to ensure the liquid enters all the tiny areas and to avoid air becoming trapped inside creating air bubbles.
8. After 1 hours , the stone mixture should be set. VERY gently remove the mold away from the casting. You can very carefully use a knife to help open the mold or by hand. Ensure open it very slow to ensure that you do not break the casting.
9. Once the casting is removed you may see a little powder on the surface. It can be washed by water, and air dry over 24 hours.
10. Paint Coat: After 24 hours you can paint your beautiful completed casting any color you wish.

Important: Do not add too much water to the powder mixture or they will not be set correctly and your casting will not succeed.

Reviews

There are no reviews yet.

Be the first to review “DIY Baby Plaster Mold 3D Hand Foot Print Mold for Baby Souvenir Hand Casting Kit Couples Wedding Accessories Home Decor Gifts”

Your email address will not be published. Required fields are marked *